Gogged's 2018 JLUR

**Gogged** · June 9, 2019, 4:01am

So, ordered this 6/21 and it showed up 7/18. Jeep was moving fast…

Ordered the following packages:
Infotainment/electronic package
Tan leather(hate the red dash)
Automatic
Trailer tow/electrical package(aux switches)
Cold weather group

![JOflsbS|666x500]
Metalcoak Gamechanger 3.5" Rocksport Edition & LOD Sliders
ATX Chamber Pro II 17"
Cooper 37" x 13.5 STT Pro

Cant remember name of antenna mount
Midland CB, not hardwired so I can take out when not wheeling

Metalcloak Undercloak Skid System
Dana Diff covers front/back
Metalcloak Rear Diff Skid
(upload://cOmQZ5ts3SOVOfZHSMM81tL8Zib.jpeg) ![YpN6cwT|375x500]
LOD Rear Bumper/Tire Carrier
Rigid Flush Mount LED…6000 lumens to help reverse lights
(upload://rDs8DQG8Q1BU91eXIi1LL8CywhL.jpeg)
Adams 1350 driveshafts front/rear

Regeared to Yukon 4:88
While at ORI for regear, had the put EVO truss front axle/Cs

**john** · June 9, 2019, 2:42am

CoolTech is the name

**Buckeye** · June 9, 2019, 11:17am

Very nice build!

**Gogged** · June 11, 2019, 10:47am

Adams Driveshafts courtesy of Jeremy![IMG_1817|666x500]

**R3DLEG** · June 11, 2019, 11:31am

Doing it right man, good work!

**x7tristan** · June 11, 2019, 1:06pm

Looks really good @Gogged! But where are those pink rock lights!?

**Gogged** · June 13, 2019, 2:44am

SteerSmarts “No Drill” Top Mount Drag Link/Track Bar Bracket/Tie Rod/Stabilizer clamp…don’t mind the beat to heck stabilizer…was mounted low before…needs replaced

**R3DLEG** · June 13, 2019, 2:28pm

That’s good shit right there. Except that stabilizer, that’s not good shit, just shit. But it will work!

**Gogged** · June 27, 2020, 12:36pm

Added a Redneck Ram, and a Steersmarts track bar

**Gogged** · June 27, 2020, 1:11am

Genright Bumper, always hated the Metalcloak one

**Frank** · June 29, 2020, 1:56pm

Looks good Josh. So does the redneck ram eliminate the stabilizer? Is it using the same mounts?

**john** · July 2, 2020, 2:19pm

Since Josh hasn’t answered you I’ll chime in. Yes it eliminates the stabilizer and you should weld tabs axle side and run an appropriate bracket on the tie rod. The ram is pretty strong and it will destroy a stabilizer bracket.

**Gogged** · December 15, 2020, 10:06am

Added Artec front fender liners…a while ago…a little behind

**Gogged** · December 15, 2020, 10:08am

Added a Molle Platform Solutions overhead rack a while back…stock pic

**Gogged** · December 15, 2020, 10:10am

Added Midland GMRS MXT115 along with the President CB radio

**Gogged** · December 17, 2020, 2:48am

Oh and the BFG KM3 39s…Cooper 37s were beat to hell… BFG 39s were only another 4 lbs each…

**Gogged** · February 27, 2022, 11:31am

Savvy Magnaflow muffler…old one was beat up bad, rattling because the hanger bracket was broken…new one sits much higher, keeps the stock resonator so doesn’t sound terrible, normal drone is a bit louder but not annoying

**Gogged** · February 28, 2022, 12:59pm

Atomic Monkey extinguisher holders…

Oracle Flush Mount LEDs

**dajanx** · March 7, 2022, 9:46pm

I really dig those tail lights, and you get to keep the sensors damn thats legit.